- #WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE HOW TO#
- #WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE INSTALL#
- #WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE UPGRADE#
This type of pool pump is highly efficient because you can set the exact flow rate you need. Variable-speed pool pumps use a permanent magnet motor, unlike the induction motor of one and two-speed pool pumps.The higher speed option is best used with your heater and whenever you are cleaning your pool. Two-speed pool pumps allow you to harness the efficiency of a lower speed as it’s not recommended to use a high speed at all times.They operate at a constant speed, are inefficient because of the high pumping speed, and can be quite noisy. Single-speed pool pumps are the basic, most traditional type of pool pumps.
#WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE UPGRADE#
If you do choose to upgrade the pool pump, a good option to go with is a variable-speed pool pump.Īs opposed to one and two-speed pool pumps, variable pool pumps offer more power, longevity in operation, and efficiency. One easy fix for this is by upgrading the pool pump to provide the necessary pressure.
#WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE INSTALL#
A lot of times, when you first install a pool heater, the pool pump may not be strong enough to bring water into the heater with an adequate amount of pressure. If the pool pump is not operating with enough power, this can cause your pool heater to have issues. Lastly, you want to make sure that you’re running your pump for at least 8 hours. Also, make it a point to keep the filter media clean as well. When checking your pool filter, make sure that you empty the skimmer and the pump baskets weekly. If you have a dirty filter with a lot of blockage, this will keep your pool heater from receiving an adequate amount of water. To make sure that your pool heater is getting enough water, you need to check your filter. Pool heaters rely on a steady stream of water in order to operate properly, and when this is interrupted, you will start to run into issues. If your pool heater is not getting enough water, then this could cause it to be faulty. Along with that, it allows the pool heater to pump a lot more efficiently as well because it’s operating in a warmer environment. This solar cover helps keep your heater from losing any heat that it generates during its run time. One neat DIY trick to use when regulating the temperature is setting a solar cover on your pool heater. Typically, it needs to be at least 60 degrees out in order for your pool heater to function the best way possible. But with many units, once you dip below 50 degrees, the pool heater will not be as effective at doing its job. Some heat pumps can operate under low-temperature environments, with some running smoothly as low as 30 degrees. There are different types of pool heaters, including gas and electric heaters, that will work just fine during cold weather, though some operate better than others. With some pool heat pumps, if it is not warm enough, the heater will not run and keep up the water. This way, the water being pumped in is actually warmer.
![where to find the filter area of aquaterm furnace where to find the filter area of aquaterm furnace](https://scotthomeinspection.com/wp-content/uploads/2016/10/20160803-81-e1475616707656.jpg)
If your pool heater is not set to a high enough temperature, then it may not appear to be working (though it’s working just fine).Įnsure that the pool heater’s thermostat has a higher temperature setting than the current water temperature of your pool.
![where to find the filter area of aquaterm furnace where to find the filter area of aquaterm furnace](https://i.pinimg.com/originals/7f/94/70/7f9470250117f8d812dacaae60577e41.jpg)
![where to find the filter area of aquaterm furnace where to find the filter area of aquaterm furnace](http://i1.ytimg.com/vi/-lO4xAsTyqM/hqdefault.jpg)
Most pool heaters are incredibly temperamental when it comes to the temperature you set it at and the outdoor temperature. Checking the breaker, resetting the unit, and going over connections is the step you will want to take. In this case, you will want to check your power sources and connections to make sure everything is as it should. If you do not see an error message and instead, your pool heater just shuts off immediately after or shortly after turning it on, then this can be an indication of a power issue. Reasons that your pool heater may not be getting enough water include filter issues and pressure issues. If you see error codes, including “Lo/Hi” or “Flo,” then this is usually an indication that your pool heater is not getting enough water. Your first step would be to take a look at any error codes that might be displayed. If you find that your power heater turns on but then keeps shutting off, this could indicate that you are having water pressure issues. As you inspect, keep a close eye on damaged wiring and take a look at the breaker to ensure that the pump is getting enough power to operate. Sometimes the fix can be as simple as making sure the pool heater is plugged in properly.Ĭheck to make sure that your pool heater is properly connected to the power source and that there are no electrical connection issues.
![where to find the filter area of aquaterm furnace where to find the filter area of aquaterm furnace](https://www.hvac.com/wp-content/uploads/2019/02/Merv_13_air_filter.jpg)
When you are working on troubleshooting a pool heater, one of the most common culprits is the power source.
#WHERE TO FIND THE FILTER AREA OF AQUATERM FURNACE HOW TO#
But what do pool owners do if they run into issues with getting that water to heat up? In my handy guide, I will go over some of the most common ways of how to troubleshoot a swimming pool heater so that you are up and running again. Having a pool heater is a great way to enjoy a warm dip in the pool as the summer months dwindle away.